Remote control SICETECH WHY EVO Universal multifrequency gate garage door V.20

Description: 4 COLORS ---- MAGNOLIA WHITE , LICORICE BLACK , SKY BLUE, GRANADE RED ---- WHY EVO 2022. V 20+ NEW by ITALY Item descriptionUp to 4 different remotes in ONE! Every button of WHY EVO can be programmed as a replacement for a different brand, so using only one transmitter you can control up to 4 devices from different producers. WHY EVO multi is a replacement for fixed and rolling code remotes with the frequency from 280 to 868 MHz.Technical features:Number of channels: 4Code: fixed, rollingFrequency: 280-868 MHz AM/FMPower supply: 3V battery, type CR2032Dimensions: 51x41x10 mmBattery and instruction included Copying Procedure for the Remote Control WHY EVO RTB-EVOLUTION Small, aesthetic, solid with an anti-shock rubber edging, quality made in ITALY. LIST OF COMPATIBLE REMOTES FOR D.O.R. PROCEDURE WHY EVO is the first universal remote control that replaces 4 different remotes(based on fixed or rolling code) for automatic doors or gates.FIXED CODE DUPLICATING PROCEDURESWhile pressing the button 1 of the “WHY EVO”, press 4 times the buttonRelease both buttons. Now the led of the WHY emits a quick flash every 2 sec.Place the original remote control in front of the “WHY EVO”, at about 4-5 cm of distance (as shown in the picture below).Press and retain pressed the button of the original remote control that you want to copy until the WHY’s LED will change frequency of flashing (faster than before), as a confirmation of the correct copy of the code.While the LED is flashing, press the button of the “WHY EVO” where you want to store the code just copied, until the led turns off.The copy has been applied with success. Verify on the automation the orderly functioning of the new WHY EVO remote control. Note: If the LED will flash only 3 times and than will turn off, it means that the code hasn’t been copied well. In this case repeat the operation from the point 1.The memory of the “WHY EVO” is completely re-writable.To duplicate a second button, repeat the operation from the point 1. ROLLING SIMPLE DUPLICATING PROCEDURES While pressing the button 1 of the “WHY EVO”, press 4 times the button 2.Release both buttons. Now the led of the WHY emits a quick flash every 2 sec.Place the original remote control in front of the “WHY EVO”, at about 4-5 cm of distance (as shown in the picture below).Press and retain pressed the button of the original remote control that you want to copy until the WHY’s led will change frequency of flashing (faster than before), as a confirmation of the correct copy of the code.While the LED is flashing, press the button of the “WHY EVO” where you want to store the. code just copied, until the led will turn off.The copy has been successfull.Proceed with the remote control recognition on the receiver by the D.O.R. procedure (verify the models list) or follow the producer’s methods. Note: If the LED will flsh only 3 times and than will turn off, it means that the code hasn’t been copied well. In this case repeat the operation from the point 1.The memory of the “WHY EVO” is completely re-writable.To duplicate a second button, repeat the operation from the point 1.To activate the remote control on the receiver for models marked with D.O.R., proceed as below:First of all you must be close to the automation (eg. receiver).Press and retain pressed the programmed button for about 10 sec, when the LED start to flash,release the button.Wait until the LED will turn off. The operation has been done, now you can use your new remote control.To activate on the receiver all the others models:Refer to the instructions of the original model. NOTE: The seed code of the WHY EVO can be emitted as below:Press the buttons 1 and 2 simoultaneously for 8 sec. and release them when the LED start to flshWhile the LED is flshing press the button with the seed code needed.ATTENTION!! Every kind of receiver can have the “radio-mode” disarmed. In this case it will be necessary to programm the new remote control with the “manual procedure”. ROLLING COMPLEX DUPLICATING PROCEDURESBFT While pressing the button 1 of the “WHY EVO”, press 4 times the button 2.Release both buttons.Now the LED of the WHY emits a quick flsh every 2 sec.Place the original remote control in front of the “WHY EVO”, at about 4-5 cm of distance.Press and retain pressed the button of the original remote control that you want to copy until the WHY’s led will turn on with a light and then emits a double flash every 2 sec.Transmit now the seed code of the original remote control (by pressing the rear hide button or the buttons 1 and 2 simultaneously in the new models)Now the LED will flsh quickly, press the button of the “WHY EVO” where you want to store the code just copied, until the LED will turn off.Now activate the procedure to insert the new remote control on the receiver.FAAC SLH 433 - 868 GENIUS 868ATTENTION, PLEASE: Verify that the remote control is a MASTER.Pressing any buttons, the LED should issue a double flash rather than switch on as a fixed light. While pressing the button 1 of the “WHY EVO”, press 4 times the button 2.Release both buttons.Now the LED of the WHY emits a quick flsh every 2 sec.Predispose the FAAC remote control for the emission of the seed code (by pressing simultaneously the buttons 2 and 3)While the FAAC LED is flashing, place it in front of the “WHY EVO”, at about 4-5 cm of distance and press the button that you want to copy until the WHY’s led will change frequency of flashing (faster than before), as a confirmation of the correct copy of the code.While the LED is flashing, press the button of the “WHY EVO” where you want to store the code just copied, until the led will turn off. To activate the remote control on the receiver for models marked with , proceed as below: First of all you must be close to the automation.Press and retain pressed the programmed button for about 10 sec, when the LED start to flash, release the button.Wait until the LED will turn off. The operation has been done, now you can use your new remote control.To activate on the receiver all the other models: Refer to the instructions of the original model.NOTE: The seed code of the WHY EVO can be emitted as below: Press the buttons 1 and 2 simoultaneously for 8 sec. and release them when the LED start to flshWhile the LED is flshing press the button with the seed code needed.ATTENTION!! Every kind of receiver can have the “radio-mode” disarmed. In this case it will be necessary to program the new remote controls with the “manual procedure”. THIS SPECIFIC ITEM IS NOT DESIGNED FOR AMERICAN MARKET AND AS SUCH IT HAS NO APPLICABLE FCC Declaration of Conformity RULES

Price: 24.49 USD

Location: Krizevci, CA

End Time: 2023-07-28T04:32:08.000Z

Shipping Cost: 8 USD