Description: Features: Condition:100% Brand New Color:Black Light Color: Red/Blue/Green 1-6 Gear display Instructions Guide: You need to connect 4 wires to the bike’s wiring harness. Good quality quick connectors are supplied (4 pcs wire taps). No need to cut any wires and no need for soldering. All connections can be done either under the fuel tank, at the ECU box or behind the instrument cluster. The table below shows the connection overview: GFYSHIP wire Connect to Red +12V switched power lead Black Ground lead or chassis ground White Speed Signal, tap anywhere between the Speed Sensor and instrument cluster. On some ABS models, tap the speed signal anywhere between the ABS computer and ECU box. Green Tacho signal, tap anywhere between the ECU box and instrument cluster. Alternatively, tap the signal wire from the 2-wire Crankshaft Sensor (Pickup coil), anywhere between the sensor and ECU box. To complete the install, it is recommended that you consult with your dealer and/or refer to the Service Manual available for your bike. Due to the large number of bike models and vehicles compatible with this Kit, model specific wire colors and install instructions are not described in this document. 1. The ignition key should be in OFF position. Remove the seat, raise and support the fuel tank 2. Locate the Speed Sensor coupler. A. Most motorcycles have the speed sensor mounted on the gearbox. Others have the sensor mounted either at the front or at the rear wheel. B. Trace the cable until you find the speed sensor coupler. It is a 3-pole connector (except BMW, which use 2-pole). C. If in doubt, check the bike’s Service Manual or ask your dealer for the location of the Speed Sensor coupler. Confirmation: Separate the Speed Sensor coupler. Rotate the wheels while the ignition is on. The speedometer should indicate 0. If so, turn the ignition off, reconnect the coupler and proceed to the next step. Otherwise, if the speedometer registers a speed other than 0, you have not disconnected the correct coupler and need to look again. ABS models: Some bikes equipped with ABS do not have a speed sensor (e.g. Yamaha FJR1300 2006+, VMAX 2009+, Ducati ST4 2005+). The speed signal is generated by the ABS computer. On these bikes, tap the speed signal wire between the ABS computer and ECU box. Refer to the bike’s Service Manual for the wiring. 3. Connect the GFYSHIP Black wire to the Ground wire of the sensor, using the Red wire tap connector supplied. 4. Connect the GFYSHIP Red wire to a switched +12V power lead, such as the hot wire of the rear brake light switch, or to a power lead at the fusebox. You can use the Power lead of the speed sensor if its voltage is higher than 9V. Again, use the Red wire tap connector supplied. 6. Connect the GFYSHIP Green wire to the Signal wire of the Crankshaft sensor (Pickup coil). The Crankshaft sensor is inside the crankcase, usually near the alternator. It has two wires. Alternatively, tap the tacho signal wire near the ECU box. Again, use the Red wire tap connector supplied. Setup: You need to setup the module after installation. When ignition is turned on, the display counts backwards (6 to 1) indicating that the memory is clear. - Raise the rear wheel off the ground by using a stand, and start the engine in Neutral. (If you do not have a stand, you may setup the unit while riding. Find a long, straight road with light traffic.) - The display will blink “1”. Select first gear, release the clutch, and keep the RPM above idle speed. The display is blinking faster while the unit is learning the gear. - When the display shows “2”, select second gear. Repeat this process until all gears are thought (5 or 6). The unit is programmed and should indicate the gears correctly. Now, when ignition is turned on, the display counts forward (1 to 6) indicating that it is fully functional. Package Include: 1 x Gear Indicator Fitment: For Keeway K-Light 125 ALL YEARS For Keeway RKF 125 ALL YEARS For Keeway RKR 125 ALL YEARS For Keeway RKV 125 ALL YEARS For Keeway Superlight Limited 125 ALL YEARS For Keeway TXM Motard 125 ALL YEARS For Laverda 650 Lynx ALL YEARS For Laverda SFC 750 2015 For Laverda SFC 1000 2015 For Laverda ALL With Digital Trip / ODO ALL YEARS For Malaguti Dune 125 ALL YEARS For Malaguti DuneX 125 ALL YEARS For Malaguti Monte Pro 125 ALL YEARS For Malaguti RST 125 ALL YEARS For Malaguti XSM 125 ALL YEARS For Malaguti XTM 125 ALL YEARS For Moto Morini Corsaro 1200 ALL YEARS For Moto Morini Granpasso 1200 ALL YEARS For Moto Morini Milano 1200 ALL YEARS For Moto Morini Scrambler 1200 ALL YEARS For Moto Morini Sport 1200 ALL YEARS For Moto Morini ALL With Digital Trip / ODO ALL YEARS For Motorhispania ALL With Digital Trip / ODO ALL YEARS For Munch ALL With Digital Trip / ODO ALL YEARS
Price: 51.75 USD
Location: Guangzhou,Guangdong
End Time: 2024-01-16T08:13:49.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Light Color: Blue / Green / Red
Brand: GFYSHIP
Display Range: 1-6 Gear Display
Waterproof Level: IP65
Type 01: Motorcycle LCD 1-6 Level Gear Indicator Digital Gear Meter
Installation Notes: NO